Description
- All Internal RET actuators are connected in “Cascaded SRET” configuration
- Uses the 4.3-10 connector which is 40 percent smaller than the 7-16 DIN connector
- Supports re-configurable antenna sharing capability enabling control of the internal RET system using up to two separate RET compatible OEM radios
Product Specifications
| Electrical Specifications |
| Frequency Band, MHz |
698–806 |
790–894 |
890–960 |
1695–1920 |
1920–2200 |
2490–2690 |
| Gain, dBi |
14.9 |
15.1 |
15.3 |
16.0 |
16.6 |
16.4 |
| Beamwidth, Horizontal, degrees |
66 |
64 |
61 |
60 |
61 |
70 |
| Beamwidth, Vertical, degrees |
11.8 |
10.7 |
10.0 |
10.9 |
9.9 |
8.5 |
| Beam Tilt, degrees |
2–14 |
2–14 |
2–14 |
2–14 |
2–14 |
2–14 |
| USLS (First Lobe), dB |
20 |
20 |
21 |
16 |
17 |
16 |
| Front-to-Back Ratio at 180°, dB |
31 |
29 |
30 |
33 |
38 |
32 |
| Isolation, Cross Polarization, dB |
25 |
25 |
25 |
25 |
25 |
25 |
| Isolation, Inter-band, dB |
25 |
25 |
25 |
25 |
25 |
25 |
| VSWR | Return Loss, dB |
1.5 | 14.0 |
1.5 | 14.0 |
1.5 | 14.0 |
1.5 | 14.0 |
1.5 | 14.0 |
1.5 | 14.0 |
| PIM, 3rd Order, 2 x 20 W, dBc |
-150 |
-150 |
-150 |
-150 |
-150 |
-150 |
| Input Power per Port at 50°C, maximum, watts |
250 |
250 |
250 |
200 |
200 |
150 |
| Polarization |
±45° |
±45° |
±45° |
±45° |
±45° |
±45° |
| Impedance |
50 ohm |
50 ohm |
50 ohm |
50 ohm |
50 ohm |
50 ohm |
| Electrical Specifications, BASTA* |
| Frequency Band, MHz |
698–806 |
790–894 |
890–960 |
1695–1920 |
1920–2200 |
2490–2690 |
| Gain by all Beam Tilts, average, dBi |
14.5 |
14.8 |
15.0 |
15.4 |
16.1 |
16.0 |
| Gain by all Beam Tilts Tolerance, dB |
±0.5 |
±0.5 |
±0.5 |
±0.8 |
±0.4 |
±0.4 |
| Gain by Beam Tilt, average, dBi |
2 ° | 14.5 8 ° | 14.5 14 ° | 14.2 |
2 ° | 14.9 8 ° | 15.0 14 ° | 14.5 |
2 ° | 15.2 8 ° | 15.2 14 ° | 14.5 |
2 ° | 15.4 8 ° | 15.5 14 ° | 15.2 |
2 ° | 16.1 8 ° | 16.2 14 ° | 16.0 |
2 ° | 16.0 8 ° | 16.1 14 ° | 15.9 |
| Beamwidth, Horizontal Tolerance, degrees |
±3.6 |
±3.4 |
±3.9 |
±4.6 |
±3.6 |
±7.8 |
| Beamwidth, Vertical Tolerance, degrees |
±0.9 |
±0.7 |
±0.7 |
±0.8 |
±0.7 |
±0.4 |
| USLS, beampeak to 20° above beampeak, dB |
20 |
19 |
18 |
16 |
17 |
16 |
| Front-to-Back Total Power at 180° ± 30°, dB |
19 |
20 |
21 |
28 |
28 |
26 |
| CPR at Boresight, dB |
23 |
22 |
24 |
16 |
21 |
16 |
| CPR at Sector, dB |
9 |
7 |
8 |
9 |
9 |
6 |
| General Specifications |
| Operating Frequency Band |
1695 – 2690 MHz | 698 – 960 MHz |
| Antenna Type |
Sector |
| Band |
Multiband |
| Performance Note |
Outdoor usage |
| Total Input Power, maximum |
900 W @ 50 °C |
| |
| Mechanical Specifications |
| RF Connector Quantity, total |
12 |
| RF Connector Quantity, low band |
4 |
| RF Connector Quantity, high band |
8 |
| RF Connector Interface |
4.3-10 Female |
| Grounding Type |
RF connector inner conductor and body grounded to reflector and mounting bracket |
| Radiator Material |
Low loss circuit board |
| Radome Material |
Fiberglass, UV resistant |
| Reflector Material |
Aluminum |
| RF Connector Location |
Bottom |
| Wind Loading, frontal |
685.0 N @ 150 km/h | 154.0 lbf @ 150 km/h |
| Wind Loading, lateral |
232.0 N @ 150 km/h | 52.2 lbf @ 150 km/h |
| Wind Loading, maximum |
889.0 N @ 150 km/h | 199.9 lbf @ 150 km/h |
| Wind Speed, maximum |
241 km/h | 150 mph |
| |
| Dimensions |
| Length |
1828.0 mm | 72.0 in |
| Width |
498.0 mm | 19.6 in |
| Depth |
197.0 mm | 7.8 in |
| Net Weight, without mounting kit |
38.0 kg | 83.8 lb |
| |
| Remote Electrical Tilt (RET) Information |
| Input Voltage |
10–30 Vdc |
| Internal RET |
High band (4) | Low band (2) |
| Power Consumption, idle state, maximum |
1 W |
| Power Consumption, normal conditions, maximum |
8 W |
| Protocol |
3GPP/AISG 2.0 (Single RET) |
| RET Hardware |
CommRET v2 |
| RET Interface |
8-pin DIN Female | 8-pin DIN Male |
| RET Interface, quantity |
1 female | 1 male |
| |
| Packed Dimensions |
| Length |
2010.0 mm | 79.1 in |
| Width |
608.0 mm | 23.9 in |
| Depth |
352.0 mm | 13.9 in |
| Shipping Weight |
52.2 kg | 115.1 lb |
Regulatory Compliance/Certifications
| Agency |
Classification |
| RoHS 2011/65/EU |
Compliant by Exemption |
| ISO 9001:2015 |
Designed, manufactured and/or distributed under this quality management system |
| China RoHS SJ/T 11364-2014 |
Above Maximum Concentration Value (MCV) |
